Page 91 from 112
Regulatory compliance notices 91
Class A equipment
Class B equipment
Page 92 from 112
Regulatory compliance notices 92
This product may be provided with an optical storage device (that is, CD or DVD drive) and/or fiber optic
transceiver. Each of these devices contains a laser that is classified as a Class 1 Laser Product in
accordance with US FDA regulations and the IEC 60 825-1. The product does not emit hazardous laser
Each laser product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser
Notice No. 50, dated May 27, 2001; and with IEC 60825-1:1993/A2:2001.
Use of controls or adjus tments or performance of pr ocedures other than those
specified herein or in the laser product's insta llation guide may result in hazardous radiation
exposure. To reduce the risk of exposure to hazardous radiation:
• Do not try to open the module enclosure. There are no user-serviceable components inside.
• Do not operate controls, make adjustments, or perform procedur es to the laser device other
than those specified herein.
• Allow only HP Authorized Servic e technicians to repair the unit.
The Center for Devices and Radiological Health (C DRH) of the U.S. Food and Drug Administration
implemented regulations for laser pr oducts on August 2, 1976. These re gulations apply to laser products
manufactured from August 1, 1976. Compliance is mandatory for prod ucts marketed in the United States.
Battery replacement notice
The computer contains an internal lithium manganese dioxide, a vanadium
pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not
properly handled. To reduce the risk of personal injury:
• Do not attempt to recharge the battery.
• Do not expose the battery to temper atures higher than 60°C (140°F).
• Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.
Batteries, battery packs, and accumulators should not be disposed of together with the general
household waste. To forward them to recycling or proper disposal, use the public collection system
or return them to HP, an authorized HP Partner, or their agents.
For more information about battery replacement or prop er disposal, contact an authorized reseller or an
authorized service provider.
Taiwan battery recycling notice
The Taiwan EPA requires dry battery manufacturing or importing firms in accordance with Article 15 of
the Waste Disposal Act to indicate the recovery ma rks on the batteries used in sales, giveaway or
promotion. Contact a qualified Taiwanese recycler for proper battery disposal.
Page 93 from 112
Regulatory compliance notices 93
Power cord statement for Japan
Page 94 from 112
Electrostatic discharge 94
Preventing electrostatic discharge
To prevent damaging the system, be aware of the precautions you need to follow when setting up the
system or handling parts. A discharg e of static electricity from a finger or other conductor may damage
system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the
To prevent electrostatic damage:
• Avoid hand contact by transporting and st oring products in static-safe containers.
• Keep electrostatic-sensitive parts in their containe rs until they arrive at static-free workstations.
• Place parts on a grounded surface before removing them from their containers.
• Avoid touching pins, leads, or circuitry.
• Always be properly grounded when touching a static-sensitive component or assembly.
Grounding methods to prevent electrostatic
Several methods are used for grounding. Use one or more of the following methods when handling or
installing electrostatic-sensitive parts:
• Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis. Wrist
straps are flexible straps with a minimum of 1 megohm ±10 percent resistance in the ground cords.
To provide proper ground, wear the strap snug against the skin.
• Use heel straps, toe straps, or boot straps at stan ding workstations. Wear the straps on both feet
when standing on conductive floors or dissipating floor mats.
• Use conductive field service tools.
• Use a portable field service kit with a folding static-dissipating work mat.
If you do not have any of the suggested equipment fo r proper grounding, have an authorized reseller
install the part.
For more information on static electricity or assistan ce with product installation, contact an authorized
Page 95 from 112
Operating 10 °C to 35 °C (50 °F to 95 °F)
Shipping -30 °C to 50 °C (-22 °F to 122 °F)
Storage -30°C to 60°C (-22°F to 140°F)
Maximum wet bulb
°C (82.4 °F)
Operating 10% to 90%
Non-operating 5% to 95%
* All temperature ratings shown are for sea level. An altitude derating of 1°C per 300 m (1.8°F per 1,000 ft) to
3048 m (10,000 ft) is applicable. No direct sunlight allowed.
** Storage maximum humidity of 95% is based on a maximu
m temperature of 45°C (113°F). Altitude maximum for
storage corresponds to a pr essure minimum of 70 KPa.
Height 8.59 cm (3.38 in)
Depth 66.07 cm (26.01 in)
Width 44.54 cm (17.54 in)
Weight (maximum) 27.22 kg (60 lb)
Weight (no drives installed) 20.41 kg (47.18 lb)
Rated input voltage 100 to 132 VAC, 200 to
Rated input frequency 50 Hz to 60 Hz
Rated input current 10 A at 100 VAC
4.9 A at 200 VAC
Rated input power 980 W at 100V AC input 960 W at 200V AC input