Page 16 from 33
3.Adjust the monitor's height so that it is parallel to your eye height for a comfortable viewing position.
Figure 3-9 Adjusting the Height
NOTEIf the display head is locked in the lowest height position, push down on the display head,
press the button on the base to unlock, and then lift the monitor display head to the desired height.
10 Chapter 3 Setting Up the MonitorENWW
Page 17 from 33
Turning on the Monitor
1.Press the power switch to turn on the computer.
2. Press the master power switch on the rear of the LCD.
3. Press the power button on the front of the monitor.
CAUTION Burn-in image damage may occur on monitors that display the same static image
on screen for a prolonged period of time.* To avoid burn-in image damage on your monitor
screen, you should always activate a screen saver application or turn off the monitor when it is
not in use for a prolonged period of time. Image retention is a condition that may occur on all LCD
* A prolonged period of time is 12 consecutive hours of non-use.
Connecting USB Devices
The monitor provides four USB connectors on the side panel to connect devices such as a digital
camera, USB keyboa rd, or USB mouse.
NOTEYou must connect the USB hub cable from t he monitor to the computer to enable the
USB 2.0 ports on the monitor. Refer to Step 2 in
Connecting the Monitor .
Figure 3-10 Connecting USB Devices
Using the Accessory Rails
The monitor features accessory rails on the rear th at may be used to mount optional devices, such as
the HP speaker bar, to attach to the LCD. Refer to the documentation included with your optional device
for detailed mounting instructions.
ENWW Turning on the Monitor 11
Page 18 from 33
Figure 3-11 Using the Accessory Rails Feature
Removing the Monitor Pedestal Base
You can remove the monitor pedestal to mount the mo nitor on a wall, a swing arm, or other mounting
CAUTION Before beginning to disassemble the monitor, be sure the monitor is turned off and
the power and signal cables are both disconnecte d. If your monitor has a connected audio cable,
1. Disconnect and remove the signal and power cables from the back of the monitor.
2. Slide the quick release latch (1) on the pedesta l base to the side (either right or left).
3. Pull up on the monitor display head (2) to remove it from the base.
Figure 3-12 Removing the Monitor from the Pedestal Base
12 Chapter 3 Setting Up the MonitorENWW
Page 19 from 33
Mounting the Monitor
1.Remove the monitor pedestal base. Refer to Removing the Monitor Pedestal Base in the previous
CAUTION This monitor supports the VESA industry standard 100mm mounting holes. To
attach a third party mounting solution to the monitor, four 4mm, 0.7 pitch, and 10mm long
screws are required (not provided with th e monitor). Longer screws should not be used
because they may damage the monitor. It is important to verify that the manufacturer’s
mounting solution is compliant with the VESA st andard and is rated to support the weight
of the monitor display panel. For best perfor mance, it is important to use the power and
video cable provided with the monitor.
2. Remove the HP Quick Release from the pedestal base by removing the four screws.
Figure 3-13 Removing the HP Quick Release from the Pedestal Base
ENWWRemoving the Monitor Pedestal Base 13
Page 20 from 33
3.Mount the Quick Release to a swing arm or othe r mounting fixture using the four screws removed
from the Quick Release in the previous step.
Figure 3-14 Installing the Quick Release
CAUTION The Quick Release can also be installed directly to a wall to mount the monitor
panel. It is designed to support a maximum of up to 24 lbs. (10.9 kg). If you are mounting
to a wall, HP recommends that you consult with a qualified engineering, architectural, or
construction professional to determine the appropriate type and quantity of mounting
fasteners required for your app lication and to ensure that your mounting solution is properly
installed to support applied loads.
4. Insert the monitor into the Quick Release, and then press down firmly on the monitor to lock it in
place. When the Quick Release lock s, it will make a clicking sound.
Figure 3-15 Inserting the Monitor Pa nel into the Quick Release
14 Chapter 3 Setting Up the MonitorENWW