Page 41 from 134
Operating 10% to 95% RH, non-condensing without disktte
10% to 80% RH, non-condensing with disktte
Non-operating 20% to 80% RH, non-condensing (Unpacked)
Non-operating 20% to 90% RH, non-condensing (Storage package)
Operating 5~250Hz 0.5Grms, 15mins per axis
Non-operating (unpacked) 1.04 Grms, 2-200Hz 15 mins per axis
Non-operating (packed) 1.04 Grms, 2-200Hz 15 mins per axis
Dimensions 322(W) x 294(D) x 39.4~39.9(H)mm
Weight 7.2 Ibs for 14.1” TFT LCD model with battery/7.4 Ibs for 15”LCD model with battery
I/O Ports Two Type II or one Type III PC CardBus (PCMCIA) slot
One IEEE 1394 port
One FIR port
One RJ-11 modem jack (V.92, 56K)
One RJ-45 network jack
One DC-in jack
One parallel port (ECP/EPP)
One S-video port
One external monitor port
One microphone-in jack (3.5mm mini jack)
One headphone jack (3.5mm mini jack)
Four USB ports
Drive Bays One
Indicators Power-on, Standby, Battery Status, Media Access, CapsLock and NumLock
Page 42 from 134
Page 43 from 134
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press
m during POST (when “Press to enter Setup” message is prompted
on the bottom of screen).
Press m to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
Page 44 from 134
Navigating the BIOS Utility
There are six menu options: Info., Main, System Devices, Security, Boot, and Exit.
Follow these instructions:
TTo choose a menu, use the cursor left/right keys (zx).
TTo choose a parameter, use the cursor up/down keys ( wy).
TTo change the value of a parameter, press por q.
TA plus sign (+) indicates the item has sub-items. Press e to expand this item.
TPress ^ while you are in any of the menu options to go to the Exit menu.
TIn any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values.
This menu provides you the information of the system.
Page 45 from 134
NOTE: The system information is subject to different models.
Floppy Disk Drive Shows floppy drive type informaiton.
Note: Aspre 1620, Extensa 2700, TravelMate 2500 and Extnesa 2500 series products do
not have floppy disk drive; Extensa 2000 and TravelMate 2000 series have floppy disk
HDD Model Name This field shows the model name of HDD installed on primary IDE master.
HDD Serial Number This field displays the serial number of HDD installed on primary IDE master.
ATAPI Model Name This field displays the mofel name of devices installed on secondary IDE master. The hard
disk drive or optical drive model name is automatically detected by the system.
ATAPI Serial Number This field shows the serial number of devices installed on secondary IDE master.
Serial Number This field displays the serial number of this unit.
UUID Number This will be visible only when an internal LAN device is presenting.